Electrophysiology > Electrophysiology Accessories & Equipment Products & Reviews

* "Interface" method of slice maintenance* Dual feed channels for perfusion solution* Use entire surface for multiple slices or templates* Single and dual well templates, other designs available upon request* Single well template has provision for temperature probe and ground wire* Proportional temperature controller (PTC03) with low noise performance used for heating - available separatelyThis slice recording chamber is desig…

This item is the HOLDER (BSKH) and Brain Slice Keeper (S-BSK). * Slices maintained for many hours prior to transfer to recording chamber* Simple to set up and maintain * Slices supported on a quick-change nylon net The Brain Slice Keeper has been designed to pre-incubate brain slices prior to transfer into recording chambers. It consists of a pair of closely fitting acrylic rings, upper and lower, between which is wedged a she…

* Slices maintained for many hours prior to transfer to recording chamber* Simple to set up and maintain * Many slices supported on FOUR quick-change nylon netsThe Brain Slice Keeper 4 has been designed to pre-incubate brain slices prior to transfer into recording chambers. It consists of FOUR pairs of closely fitting acrylic rings, upper and lower, between which is wedged a sheet of nylon netting. In operation, it is totally…

The MS1 chamber has been designed for use with fixed-stage upright-type microscopes. The particular feature of this chamber is the profiled contour that allows the microscope objective to sweep across the preparation when changing magnification, without having to adjust the focusing. In this way the specimen and any pre-positioned microelectrodes remain par-focal. This is particularly useful for confocal microscopy where it is…

The PC series perfusion chambers have embedded magnets that are conveniently located to retain perfusion plumbing and ground plugs. They are designed to fit into our 8090c fixed stage platform. A standard 22 mm cover slip is used to create the chamber bottom that is attached with vacuum grease, silicon, or parafilm (use a heat gun to gently melt the parafilm). There are two plastic retention screws for added security. Both ope…

The piezo solution switcher uses a high-speed piezo flexure guided nanopositioner to move pipette tips in solution switching applications. It can move an electrode tip across a 5 µm thick theta glass septum. This system is ideal for measuring cellular response to drugs or other elements in solution. Piezo movement can be triggered by either input from common recording amplifier equipment or by Siskiyou software via a LabVIEW™…

Developed through years of experience with the Flaming/Brown style micropipette pullers and infused with leading edge technology, Sutter is proud to introduce the P-1000 micropipette puller. The most obvious new feature is the color touchscreen display that provides an intuitive and full-featured interface. F E A T U R E S > P - 1 0 0 0Color touch-screen interfaceSafe heat mode to protect and extend filament lifePipette Cookbo…

A significant advance in the technology of fabrication of micropipettes, optical fiber probes, and nanospray tips, is offered with the P-2000 micropipette puller. The P-2000 integrates a CO2 laser-based heat source with the technology derived from our extensive experience with conventional pullers. This system offers capabilities unmatched by other pullers. While the P-2000 is suitable for working with most conventional glasse…

The Model P-30 vertical micropipette puller is designed for the fabrication of basic micropipettes and patch-type pipettes. It will pull micropipettes with tip diameters as small as 0.3µm and moderate taper lengths (10 to 15mm). By using an included patching attachment, the P-30 will pull the standard double pull patch-type pipette. Used with thin wall glass capillaries, it will generate pipettes or needles suitable for microi…

The Model P-97 micropipette puller is the latest generation of the Flaming/ Brown type puller for fabrication of micropipettes, patch pipettes and microinjection needles. While retaining many of the features on the Model P-87, the P-97 offers improvements in mechanical, electronic and software design. The result is better control of the pulling process and a higher degree of reproducibility. The P-97 combines a proven mechanic…

TMC’s Active Vibration Isolation Table features state-of-the-art vibration isolation performance. By integrating our new Compact Sub-Hertz Pendulum Isolation System (CSP®) for horizontal vibration reduction with our new PEPS-VX® Inertial Damper for vertical vibration cancellation, we have produced a superior, ultra-quiet table in six degrees-of-freedom. This advanced isolation technology may be combined with TMC optical tables…

63-500 Series High-Performance Lab Air TableIsolator with 4 in. CleanTop II, 1/4-20 on 1 in. spacing 36 in. x 48in., 900x1200 mmFeatures: • Gimbal Piston™ Isolators• Thin-Wall Rolling Diaphragms • All-aluminum height control valves• Internal Piston Travel Restraints• Tiebar Gussets• Rugged Built in leveling feet• Superior Table TopsTMC 63-500 Series High-Performance Lab Tables provide an excellent vibration-free working surfac…

64 Series TableTop™ PlatformsImperial Clean Top II with 4 isolators36in.x30in. (145lb) or (66kg)Effectively isolates floor vibration with unprecedented ease, portability and economy.Features: •Gimbal Piston Isolators•Top plates available in granite, stainless steel laminate and CleanTop® II steel honeycomb breadboard•Attaches to tops up to 2 1/8" thick•Isolators cradle platform for stability•Isolator housings protect isolators…

Another in a long line of TMC innovations, the 75 Series Breadboards minimize both weight and cost. A patented manufacturing technique allows us to form countersunk, tapped holes in a thin top skin of stainless steel. The holes are not drilled or punched, but fabricated in a way that effectively “thickens” the skin in a small ring around the threads. No inserts are used and the tapped holes are 3 threads deep.These tops have r…

The model P-30 vertical micropipette puller is designed for the fabrication of basic micropipettes and patch-type pipettes. It will pull micropipettes with tip diameters as small as 0.3um and moderate taper lengths (10 to 15mm). By using an included patching attachment, the P-30 will pull the standard double pull patch-type pipette. Used with thin wall glass capillaries, it will generate pipettes or needles suitable for microi…